SlackSpec
SlackSpec 43-46mm Chain Slack Min/Max Gauge 1.69–1.81 in for KTM 85 SX, Husqvarna TC 85 and GasGas MC 85 2025–2026 | Made in USA
SlackSpec 43-46mm Chain Slack Min/Max Gauge 1.69–1.81 in for KTM 85 SX, Husqvarna TC 85 and GasGas MC 85 2025–2026 | Made in USA
Couldn't load pickup availability
Free US shipping over $14.95 · 30-day free returns · Made in Arizona
Pre-order: SlackSpec 43–46 mm (1.69–1.81 in) Chain Slack Min/Max Gauge for 2025–2026 KTM 85 SX, Husqvarna TC 85 and GasGas MC 85.
Shipping note: this gauge is in development, with production starting soon. Please expect a one to two week delay before your order ships.
The SlackSpec min/max chain slack gauge checks 1.69–1.81 in (43–46 mm) chain slack on the 2025–2026 models listed under Fit and compatibility. It sits on the swingarm chain guard under the chain while you adjust.
Key features
- Min and max marked: one side is 1.69 in (43 mm) minimum slack, the other is 1.81 in (46 mm) maximum.
- Hands-free: profiled to sit on the chain guard, so it stays in place while you turn the adjusters.
Specifications
| Range | 1.69 in (43 mm) minimum to 1.81 in (46 mm) maximum chain slack. |
| Chain | 428 class (1/2 × 5/16"), the size listed in the 2018–2026 KTM 85 SX, Husqvarna TC 85 and 2021–2026 GasGas MC 85 owner's manuals. |
| In the box | 1 gauge. |
| Origin | Made in Arizona, USA: designed and 3D printed by AzJake Creations in Arizona. |
Fit and compatibility
Fits the 2025–2026 models below when the owner's manual lists 43–46 mm (1.69–1.81 in) chain slack. Both 17/14 and 19/16 wheel sizes are covered. Year ranges are [primary] from those owner's manuals.
KTM
85 SX: 2025–2026 [primary], 17/14 and 19/16. Not 2018–2024 (46–49 mm). Not 2016–2017 (55–58 mm; use the SlackSpec 55–58 mm gauge).
Husqvarna
TC 85: 2025–2026 [primary], 17/14 and 19/16. Not 2018–2024 (46–49 mm). Not 2015–2017 (55–58 mm; use the SlackSpec 55–58 mm gauge).
GasGas
MC 85: 2025–2026 [primary], 17/14 and 19/16. Not 2021–2024 (46–49 mm). There is no 2018–2020 GasGas MC 85 in the KTM-group era.
Needs a manual check
2027 KTM 85 SX, Husqvarna TC 85, and GasGas MC 85 are not in this list. 2027 KTM 85 SX parts diagrams use the same 428-class chain part as 2018–2026, but no 2027 owner's manual slack figure was found. Check the owner's manual for that exact model and year before treating 2027 as 43–46 mm.
What's in the box
1 gauge.
Use and care
- Put the bike on a lift stand so the rear wheel is off the ground, with no rider aboard.
- Set the gauge on the swingarm chain guard (chain sliding guard) under the chain, at the end of the guard.
- Adjust until the chain sits between the MIN and MAX marks. The lower chain section should be taut. Chain wear is not always even, so check more than one position.
- Tighten the axle, then remove the gauge.
- Always check final chain slack against your owner's manual. This is an aftermarket part made by AzJake Creations, not an OEM part.
FAQ
Is it compatible with a 2025 or 2026 KTM 85 SX, Husqvarna TC 85, or GasGas MC 85?
Yes, including both the 17/14 and 19/16 wheel sizes. The 2025 and 2026 owner's manuals for all three models list chain tension as 43–46 mm (1.69–1.81 in), measured by pulling the chain up at the end of the chain sliding guard with the bike on a lift stand.
Is it compatible with a 2018–2024 85 SX, TC 85, or MC 85?
No. Those years list 46–49 mm chain slack, which is a different range. This 43–46 mm gauge is only for the 2025–2026 models listed under Fit and compatibility.
Is it compatible with an earlier 85 SX or TC 85?
2016–2017 KTM 85 SX and 2015–2017 Husqvarna TC 85 are listed on the SlackSpec 55–58 mm gauge, not this one. If your bike is not listed here, check its chain slack spec in your owner's manual before ordering.
What chain slack does it set?
It checks that slack is between 1.69 in (43 mm) minimum and 1.81 in (46 mm) maximum. Always verify final chain slack against your owner's manual.
How do I use it?
With the bike on a lift stand, set the gauge on the swingarm chain guard under the chain, at the end of the guard. Turn the adjusters until the chain sits between the MIN and MAX marks, with the lower chain section taut, tighten the axle, and remove the gauge.
Is it made in the USA?
Yes. Made in Arizona, USA: designed and 3D printed by AzJake Creations in Arizona.
Free US shipping on orders $14.95 and up.
Share
